Categories
 

Roof attachment components

Roof attachment components

SnapNrack offers a variety of roof attachment components. Some may be used individually, while others require a combination of components. The flashed L-foot is recommended for simple flush mounts to a roof with composition shingles. Roofs with tile or thick roofing material will probably require standoffs. The Corrugated Roof Block allows attachment of the L-foot directly to structural members covered with corrugated metal without collapsing or crushing the ridge in the roof material. The Hanger Bolt Clamp allows a versatile installation on roof surfaces which won't allow L-feet or standoffs.

Configuring tilt angles from 0 to 10 degrees simply requires SnapNrack standoffs. A 5-1/2" standoff on the lower rail and a 7" standoff for the upper rail allows adjustability for shallow tilts. For angles from 10 to 45 degrees, use standoffs for both upper and lower rails, then extend the upper edge with sections of rail cut to length and drilled with two holes. Tilt leg rails can be cut and drilled in advance to save time on the job site. A simple drill guide will help with locating the holes in the tilt leg. If the length of the cut-rail leg exceeds 4 feet, consult a structural engineer before proceeding.

Display: List / Grid
Show:
Sort By:
FLASHING, VERDE INDUSTRIES, 1.0SSO, SOLA
Additional sub base flashing used for SnapNrack 1 or 4 hole base plate standoffs on flat and ..
$3.94
Ex Tax: $3.94
FLASHING, VERDE INDUSTRIES, 1.0STF, PIPE
FLASHING, VERDE INDUSTRIES, 1.0STF, PIPE FLASHING, SOLAR TILE STRAIGHT CONE, DEAD SOFT AL W/ ROLL..
$11.11
Ex Tax: $11.11
PIPE FLASHING, 1", GALVANIZED STEEL18" X
Typically used to flash SnapNrack 1 or 4 hole base plate standoffs on curves tile roofs. ..
$148.09
Ex Tax: $148.09
SNAPNRACK, 10-45 DEG TILT HARDWARE KIT,
Bonding Tilt Kits can be used to tilt up arrays on low-slope roofs. Warranty ..
$8.21
Ex Tax: $8.21
SNAPNRACK, BONDING MID CLAMP ASSEMBLY, 1
The Bonding Mid Clamps are pre-assembled for quick snap-in the rail installation. The t..
$2.44
Ex Tax: $2.44
SNAPNRACK, CHANNEL NUT FOR 5/16IN-18
The channel provides an unique "snap-in” installation that can be installed anywhere on the rail,..
$0.49
Ex Tax: $0.49
SNAPNRACK, COMPOSITION FLASHING W/ BASE
Base Kit w/ Flashing is recommended for simple flush mounts to a roof with composition shingl..
$6.16
Ex Tax: $6.16
SNAPNRACK, COMPOSITION L-FOOT ASSEMBLY,
The L Foot is engineered for maximum adjustability for a clean level installation, including a 1”..
$2.44
Ex Tax: $2.44
SNAPNRACK, COMPOSITION L-FOOT ASSEMBLY,
SNAPNRACK, COMPOSITION L-FOOT ASSEMBLY, BLACK The L Foot is engineered for maximum adjustabil..
$3.08
Ex Tax: $3.08
SNAPNRACK, HD STANDOFF W/ 6-HOLE BASE KI
The HD Standoff Kit w/ 6 Hole Base can be used on flat roofs that are pitched, comp shingle, ..
$10.09
Ex Tax: $10.09
SNAPNRACK, HD STANDOFF W/ 6-HOLE BASE KI
SNAPNRACK, HD STANDOFF KIT W/ 6-HOLE BASE, 12IN, CLEAR The HD Standoff Kit w/ 6 Hole Base..
$11.98
Ex Tax: $11.98
SNAPNRACK, METAL ROOF BASE ASSEMBLY, CLE
MRB provides a robust self-sealing mounting base for common corrugated metal roof profiles. ..
$3.89
Ex Tax: $3.89
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE,
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE, 10IN, CLEAR The Standoff Kit w/ 1 Hole Base can b..
$10.09
Ex Tax: $10.09
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE,
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE, 5-1/2IN, CLEAR The Standoff Kit w/ 1 Hole Base ca..
$8.10
Ex Tax: $8.10
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE,
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE, 7IN, CLEAR The Standoff Kit w/ 1 Hole Base can be..
$9.06
Ex Tax: $9.06
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE,
SNAPNRACK, STANDOFF KIT W/ 1-HOLE BASE, 8-1/2IN, CLEAR The Standoff Kit w/ 1 Hole Base ca..
$9.58
Ex Tax: $9.58
Sign up for newsletter